Curing Lights

• Stable output power guarantees constant light so that the solidification effect is not affected by the consumption of remaining power.
• Parallel light ensures more focused output energy and better solidification effect.
• Wireless charging corresponding to the standards of wireless charging protocol is available.
• Super capacity battery. A full charge can be used for more than 500 times continuously under 10s working of P2 mode, from full charge to low-battery alert.
• Aluminum alloy body, resistance to shatter and drop.
• Light source featuring 360-degre rotation to realize curing from all directions.
• Replaceable light source, 400nm-420nm light source with corresponding reagent enables detection of dental caries.
• A dedicated whitening roller, shooting teeth whitening gel with blue light to whiten teeth.
• Charger verifying radiation output of LED curing light effective or not.
• Solidified lens fixed on light source, bonded with all-ceramic veneer and adhered to crown and fiber-reinforced composite root canal post to make solidification effect better.
• Replaceable Lithium battery, Auto power-off.
• Watt high power blue LED light. Class: class 1
• LED Curing Light is applicable to some commonly-used resin based materials in dental clinic,such as 3M, Dentsply ,dentex etc.
• Equipment Safety Classification: Operation mode: Intermittent operation mode, Protection type against electric shock:class ll, power supply inside the set, Protection degree against electric shock: type B, Protection degree against inlet liquid: conventional equipment(IPXO) , Safety in the case of flammable anesthetic mixture with air, oxygen or nitrous oxide(not AP equipment or APG equipment).
• Note:  Do not sterilize the detachable head in autoclave. Please make sure to cover the unit with a disposable isolation sleeve before each use. 

Input: 100-240V 50/60Hz, 

Fuse: T1A 250V

1. Press button "△"for 1 second and release the button when the buzzer warns for once. Following three modes are available

• Full Power Mode: The screen shows “∏” The output light intensity is full-power. (recommended mode for clinical)
• Progressive Mode: The screen shows “ɲ” The output light intensity enhances gradually power output is to maximum after 5 seconds
• Pulsed Mode: The screen shows“∏∏”the blue light works in pulse manner

2. Press button "△"for 2 second and release the button when the buzzer warns for twice. Following three modes based on output of power density are available.

• Ultra High Power Density: The screen shows "P1" The power density is about 3200mW/cm.
• High Power Density: The screen shows "P2", The power density is about 2400mW/cm²
• Standard Power Density: The screen shows "P3", The power density is about 1600mW/cm².

3. Tap button "△" to select working time interval. In"P3"mode, the time interval can be chose from 1,2,3.4,5.10,15,20 25,30, 35, 40 second In"P2"mode, the time interval can be chose from 1,2,3.4,5, 10,15,20 second In"P1"mode, the time interval can be chosefrom 1,2.3, second Information on the screen is shown in the figure.

4. During the operation, put the disposable sleeve on the top of the main unit, aim the top at the correct position, press the ON/OF F button ("O" )and the main unit will produce 'Di' sound, the curing light radiates blue light and starts working according to the set modes Meanwhile, it starts counting down from the set working time interval, it stops working when counting down to ("O" )The screen displays the set working time interval again.

5. Operation can be stopped by paras the ON/OFF button ("O").

6. After a working cycle, operator can press the ON/OFF button ("O"). to start another working cycle. Stop operating if the equipment is burning obviously, let equipment cool down before restarting. Suggest continous working cycle less than 5 times.

7. Battery Indicator: Low power detective circuit is fixed inside of the main unit.If battery indicator in the screen has only 1 bar left, please charge in time.

8. When the battery needs to be charged. plug USB Type A jack in USB Type A plug of power adapter, and connect the plug of power adapter into the AC 100V-240V power supply, and connect Micro USB of USB cable into charge indicator in charge. The blue indicator light on charger indicates charger on standby. Put the main unit to the charging point of the charger, and the indicator light turns green, main unit is detected. Meanwhile,the indicator light at the bottom of main unit turn green, the curing light starts charging. When charging finished, the indicator light at the bottom of main unit turn blue.

9. After operating, take off the disposable sleeve and throw away, avoid reusing. Power output will be, decreased by 5-10% if using the disposable sleeve.

10. The product will turn off automatically if there is And operations within 2 minutes. Turn it on by pressing any button.

11. The depth of solidification or dental resin composite is not less than 4mm per 10 second. The recommended separation distance between Iuminous point and solidifying point is 2mm.

• FDA Approved.
• 5W high power blue light LED.
• Cure 2mm reins in one second, go quicker than ever.
• 360 degree plastic rotary head, extend the possibility.
• Constant power output, born for dental restoration.
• Two working modes for option, with the maximum light intensity of 2500mw/cm2.
• Especially suitable for orthodontic brackets, porcelain verneers and post-core adhensives.
• Woodpeckerrechargeable lithium battery had received CB certification. The batteries refuse explosion.
• Warranty:One year's free repair for the whole unit from the date of purchase. 

• TURBO Mode: screen shows P1, Press the time button to select of time which could be 1 and 3 seconds. Its output light intensity is about 2300mW/cm2-2500mW/cm2.
• NORMAL Mode: screen shows P2, Press the time button to select of time which could be 5, 10, 15 and 20 seconds. Its output light intensity is about 1000mW/cm2-1200 mW/cm2.
  

• TURBO Mode: screen shows P1, Press the time button to select of time which could be 1 and 3 seconds. Its output light intensity is about  2300mW/cm2-2500 mW/cm2.
• NORMAL Mode: screen shows P2, Press the time button to select of time which could be 5, 10 ,15 and 20 seconds. Its output light intensity is about 1000mW/cm2-1200 mW/cm2.

• 3 Working mode: Full, Ramping, Pulse.
• Time setting: 5s, 10s, 15s, 20s.
• Large capacity battery (can be replaced): A full charge can be used for more than 400 times continuously under 10s working time mode. Low standby power consumption with 40 days standby time.
• Constant light intensity output: The solidification effect is not affected by the consumption of remaining power. For most curing lights on the market, light intensity obviously decreases with the consumption of remaining power.
• Woodpecker light hood is made of selected quality materials and rejects Blue-light injury. Studies prove that Blue light will cause macular degeneration to retina and eyes.
• Optical fiber can be autoclaved under 135“C high temperature and 0.22Mpa high pressure and effectively avoid cross infection.

• Insert light head into the curing light hand-piece with a twisting motion，Ensure that both the direct light source head and the light curing host are fully connected to their corresponding positions
• Connect the adapter connector to the USB Type-C charging line, and then connect the power supply. The magnet tail cap at the bottom of the host can be stably adsorbed on other metal surfaces.
• After switching on the power adapter, insert the charging port or pull out the charging port, the machine will wake up automatically, and the host screen will light up
• The main panel indicator light "orange" indicates that the battery is in charge, and the light "green" indicates that the battery is full, and the machine will automatically stop charging.
• When the host is charged for one minute in an unused state, the screen will shut down automatically, and the battery will still be charged until the battery is full。
• The battery is not fully charged prior to shipment. Please charge the battery for a minimum of 4 hours prior to first use.
• To check the battery, press and hold the time switch for 4 seconds, display screen will show: a.) 4.2 – 3.7- Battery is normal b.) Lo- Battery is low
• When battery is low, curing light circuit will automatically compensate for power output or turn the light off. Always recharge the curing light when the battery is low Lo • Direct charging option from transformer for easy transportation and mobility

Note:  Do not sterilize the detachable head in autoclave. Please make sure to cover the unit with a disposable isolation sleeve before each use. 

• TURBO Mode: screen shows P1, Press the time button to select of time which could be 1s and 3s. Its output light intensity is about 2300 mW/cm2-2500 mW/cm2.
• NORMAL Mode: screen shows P2, Press the time button to select of time which could be 5s,10s ,15s and 20s. Its output light intensity is about 1000 mW/cm2-1200 mW/cm2.

• Turbo Power Mode: Press and release “M/T” Button quickly to cycle through time options which could be 1 and 3 seconds. Its output light intensity is about 2700-3000mW/cm2.
• High Power Mode: Press and release “M/T” Button quickly to cycle through time options which could be 3 and 5 seconds. Its output light intensity is about 1800-2000mW/cm2.
• Standard Power Mode: Press and release “M/T” Button quickly to cycle through time options which could be 5, 10, 15 and 20 seconds. Its output light intensity is about 1000-1200mW/cm2.

• Small but Powerful Making a Big Difference
  Full-metal body, ergonomically-streamlined and 108g lightweight design, without fatigue from extended usage periods. Anti-shock and durable.
• 7 Modes to Fully Meet a Variety of Clinical Needs
  It has Normal, high, turbo, ortho, soft, pulse, and check modes. Like an all star, O-Star is strong in performance, well-controlled and can fully meet various clinical needs.
• Light Intensity up to 3000MW/cm²
  The high light intensity brings sufficient curing depth, which can reduce the curing time and greatly improve the efficiency of resin curing.Equipped with 10w LED, bringing you full confidence in curing.
• 360° Rotatable Head Meets Various Clinical Needs
  360° Rotatable head, easy to illuminate all angles in the mouth. The low-profile head can easily reach the posterior teeth. The patient only needs to open the mouth slightly and enjoy comfortable treatment.
• Less Light Loss
  The light intensity of curing lights decreases when the distance of the curing light increases. Compared to other curing lights (VALO Cordless / Bluephase PowerCure) the O-Star undergoes less light loss.
• Uniform Beam, Strong Penetrability
  More-focused light output thanks to the light angle of only 15.8º, ensuring good deep curing effect.
• Charging Base with Built-in Light Meter
  There is a light meter built in to the charging base. Accurate light intensity is required for efficient polymerisation of the resin, bringing you and your patients the best treatment experience.
• Simple Two-button Design Enables Easy Operation
  Equipped with OLED screen, the mode, light intensity and time can be clearly displayed to avoid clinical errors.

• Working mode setting
  Short press the “M/T” button to select the working mode. Seven working modes can be selected: Normal, High, Turbo, Ortho, Soft, Pulse and Check. Because the curing time of different modes is different, when switching modes, the curing time will automatically follow the switching.
  
• Curing time setting
  Long press the “M/T” button to change the curing time. Different working modes have different curing times.

• One year warranty
• Tips: In order to protect the device, pls remember to wear a disposable isolation sleeve before using.

• LED Screen, high quality plastic handle.
• Noiseless and no vibration when working
• Lithium battery with large capacity
• Three Modes: Gradually mode/Flashing mode/All light mode
• Automatically power down: It will be turned automatically off automatically without pressing button for 3 minutes.
• Solidification time is :40 s. Every ten seconds, sound signal to remind operator. The length of work time can be controlled freely. 
• It has self-protection against exceeding heat after continuous long time work that power– off  by itself. After the temperature is normal, operator can use it again.
• The LED is longevity. Cold light source, no fan. Avoid the infection, cause of air movement. 

• This high power 2000mw/c㎡ LED Curing Light has a humanity intelligent chip with a high intensity
• LED light and Li-on rechargeable battery.
• This device can cure all the dental resin known in the market nowadays; with a performance level far
• Superior than the halogen curing light's, it has 3 different working modes and it can solidify 4-5 mm
• Deepness in a few seconds.
• Please note that there is an isolation film at the bottom of the electromagnetic field, which needs to be removed before first use.

• Very convenient to operate.
• Small size,cordless and light weighted.
• No dazzling strong light which allows you to aim the light to the exact position and improve the effectiveness of the treatment.
• No vibration, noiseless operation.
• High power rechargeable battery.
• High powerful light intensity with a maximum reach of 2000MW/cm2.
• 3 different working time modes, exposure time for optional curing: 8s/6s/4s.
• Light guide can rotate through 360°
• You can select the correct mode according to the different types of material you wish to cure,their speed of reaction,and the clinical protocol you are following.

• Mono-fiber glass light guides for various applications.
• Anodized aluminum hand-piece.
• Latest generation of CMS electronics.
• Very high-quality single L.E.D.
• Lithium ion battery with no memory effect

• Silent and hygienic, no fan.
• Round surfaces allow for easy and comfortable manipulation.
• Compact, lightweight and well-balanced light guide rotates through 360°.
• Base-charger can be turned in all directions and low battery warning.
• Can be used anywhere in the world. The voltage input is 110 V-240 V and we will provide you with the correct adapter according to the shipping destination.

1* LED Curing Light Device

1* High Capacity Rechargeable Battery

1* Charger

1* Charger Socket

• Three working modes: Full, Ramping, Pulse. 
• Setting time: 5s, 10s, 15, 20s.
• Large Capacity Battery. 
• A full charge can be used for more than 400 times continuously under 10s working time mode. 
• The solidification effect is not affected by the consumption of remaining power.
• Low stability power consumption with forty days' stand by time.

• Power input: AC100V-240V  50Hz/60Hz
  
• Light output: 1000mW/cm² -1200mW/cm²
  
• Net weight : 120g
  
• Dimensions: Φ23mm × 263mm

• TURBO Mode: screen shows P1, Press the time button to select of time which could be 1 and 3 seconds. Its output light intensity is about 2300 mW/cm2-2500 mW/cm2.
• NORMAL Mode: screen shows P2, Press the time button to select of time which could be 5, 10, 15 and 20 seconds. Its output light intensity is about 1000 mW/cm2-1200 mW/cm².

• STEP 1: Switch on the LED Light Cure Unit with "Power Button".
•  STEP 2: Press the mode button to set the working mode, the corresponding indicator will on when a mode set.
•  Select the appropriate Time/Mode & start using the LED Light for curing.

• HIGH Mode: screen shows P1, Press the time button to select of time which could be 1 and 3 seconds. Its output light intensity is about 2300mW/cm2-2500 mW/cm2.
• NORMAL Mode: screen shows P2, Press the time button to select of time which could be 5, 10, 15 and 20 seconds.Its output light intensity is about 1000mW/cm2-1200 mW/cm².

• Turbo Power Mode: screen shows P0, press the time button to select of time which could be 1 and 3 seconds. Its output light intensity is about 2700-3000 mW/cm².
• High Power Mode: screen shows P1, press the time button to select of time which could be 3 and 5 seconds. Its output light intensity is about 1800-2000 mW/cm².
• Standard Power Mode: screen shows P2, press the time button to select of time which could be 5, 10 ,15 and 20 seconds. Its output light intensity is about 1000-1200 mW/cm².